On this page
- How much does a concrete slab cost in Sydney in 2026?
- What does a concrete slab cost per m² by project type?
- What does a slab cost per m² by finish?
- How much of that price is the concrete itself?
- Why do published Sydney slab prices disagree so much?
- What does a concrete pad cost, and why does a small slab cost more per m²?
- What should a concrete slab installation cost include, and what gets left out?
- How accurate is a concrete slab price estimator?
- Frequently asked questions
Last reviewed: 2 November 2026
A plain concrete slab in Sydney costs between about $86 and $170 per square metre in 2026, with a typical rate near $125. Move to a decorative finish and the range climbs to $140 to $230. Those figures come from independent Sydney cost tables, not from us, and the gap between the low and high ends is where nearly every pricing argument starts.
At a glance
- Plain slab in Sydney: $86 to $170 per m², typically around $125
- Across project types, most Sydney slabs land between $75 and $175 per m²
- Ready-mix concrete alone is $345 to $550 per m³, typically around $435
- At typical rates the concrete is roughly a third of the installed price
- Published ranges differ because they measure different scopes, not because someone is wrong
How much does a concrete slab cost in Sydney in 2026?
The most defensible single number for a plain residential slab in Sydney is $86 to $170 per square metre, with a typical figure around $125. That range is GST inclusive, Sydney metro, and reflects rates reviewed in November 2026.
Other published Sydney tables put a basic 25 MPa, 100mm, broom-finished slab lower, at $75 to $130 per square metre, and put most Sydney slabs of any kind between $75 and $175. All of these are 2026 figures and all of them are defensible. The section on why prices disagree explains why they do not match, and why that matters more than which one you believe.
What does a concrete slab cost per m² by project type?
Project type changes the rate more than most homeowners expect, because each one carries a different area, a different volume of concrete and a different amount of preparation.
| Project type | Typical area | Total installed cost | Cost per m² |
|---|---|---|---|
| House slab (raft) | 80 to 150 m² | $10,000 to $28,000 | $100 to $175 |
| Garage floor, single | 30 to 40 m² | $3,200 to $6,000 | $90 to $145 |
| Garage floor, double | 50 to 65 m² | $5,000 to $10,000 | $85 to $135 |
| Alfresco or patio | 20 to 50 m² | $2,800 to $9,000 | $80 to $160 |
| Garden shed floor | 15 to 30 m² | $1,800 to $4,500 | $75 to $120 |
| Concrete path, 1m wide | Per lineal metre | $130 to $220 per lineal metre | n/a |
Notice the direction of travel. The shed floor is the cheapest per square metre and the house slab is the dearest, even though the house slab is the biggest job. Size pulls the rate down, engineering pushes it up, and the house slab wins because a structural engineer and a soil classification sit behind it.
Our own shed slab and house slab pages set out what each job involves on site. If you want to understand how the soil drives the design before price enters, our guide to raft slab versus waffle pod slab is the place to start.
What does a slab cost per m² by finish?
Finish is the second axis and often the bigger one on a job of fixed size. Sydney rates for 2026, GST inclusive:
| Finish | Low | Typical | High |
|---|---|---|---|
| Plain concrete, broom | $86/m² | $125 | $170 |
| Coloured concrete | $110/m² | $160 | $230 |
| Exposed aggregate | $140/m² | $185 | $230 |
| Stamped or stencilled | $140/m² | $180 | $230 |
| Polished, polishing an existing slab | $69/m² | $125 | $195 |
| Polished, new slab poured and mechanically polished | $185/m² | $240 | $300 |
At the typical rates, 30 square metres costs about $3,750 plain, $4,800 coloured and $5,400 stamped. That is a $1,650 spread on an identical footprint, purely on finish. Our post on exposed aggregate for Sydney driveways covers what that finish involves and where it works.
How much of that price is the concrete itself?
Ready-mix concrete at 25 MPa, delivered and supplied only, runs $345 to $550 per cubic metre in Sydney in 2026, with a typical figure near $435. A 120 square metre house slab pour is quoted in one Sydney breakdown at roughly $340 to $370 per cubic metre, near the bottom of that band on a full-truck load.
Here is the calculation that matters. A 100mm slab uses 0.1 cubic metres of concrete per square metre. At a typical $435 per cubic metre, that is about $43.50 of concrete per square metre, against a typical installed plain slab rate of $125. Concrete is roughly a third of what you pay per square metre.
That is what concrete cost per m3 actually buys you: material only. The other two thirds is excavation, sub-base, reinforcement, formwork, labour, finishing, joints and disposal. Any quote that reads as though concrete is the whole job has not been itemised.
Why do published Sydney slab prices disagree so much?
Five reasons, and none of them involve anyone lying.
Scope. A "plain concrete slab" in one table and "N25, 100mm, broom finish" in another are not the same specification, even though both describe a grey slab. The second has named its grade, its depth and its finish.
GST. Some published tables state prices GST inclusive and some quote ex-GST. On a $5,000 job that is a $500 difference for identical work.
Job mix. A table weighted toward house slabs will show a higher average than one weighted toward sheds and paths.
Time. Sydney concreting costs moved about 5.5% over the past year. A guide's review date matters as much as its number.
Size. Fixed costs spread differently across 20 square metres than across 200.
What does a concrete pad cost, and why does a small slab cost more per m²?
A concrete pad sits at the bottom of the range, commonly $75 to $120 per square metre for a shed or garage floor, because a pad is small, uniform, lightly prepared and plainly finished. A single garage slab of 36 square metres typically comes in at $3,500 to $6,500 installed, and a double at $5,500 to $10,000.
The per square metre rate still rises as the job shrinks. Mobilisation, the excavator, the crew, the formwork setup and the truck's minimum load cost much the same whether you pour 9 square metres or 40. Combining a shed slab, a path and a patio into one visit is the most effective way to pull the rate back down.
What should a concrete slab installation cost include, and what gets left out?
A concrete floor slab cost should be itemised. On a 120 square metre slab on moderately reactive soil, a published Sydney breakdown runs: geotechnical report $800, structural engineering $1,200, formwork and edge boards $2,400, DGB20 base at 100mm with compaction $2,400, damp proof membrane $600, reinforcement $3,600, ready-mix and pump $5,100 to $5,550 plus $800 pumping, labour to pour and finish $3,600, and contractor margin at 15% of $2,975. Total about $23,025, or roughly $190 per square metre.
Three things to check. First, reinforcement: simple SL72 mesh runs about $8 per square metre while engineered bar cages run $30 to $50 per square metre, and that difference is invisible unless it is written down. Second, pumping: tight Sydney sites often need it, at $600 to $900 per day. Third, disposal of excavated material, which is real work and easy to leave off.
Commonly excluded and worth confirming in writing: soil testing, engineering and certification, council fees, demolition of an existing slab, and difficult-access allowances. Our guide to getting a concrete quote in Sydney covers the red flags.
One non-negotiable. NSW requires a contractor licence for residential work once the job exceeds $5,000 in labour and materials including GST, which a typical exposed aggregate driveway comfortably does. KMA has held Lic 219967C since 1999. Ask for the number and check the name matches the business on the quote.
How accurate is a concrete slab price estimator?
An online concrete slab cost calculator or price estimator returns a range, and a range is all it can honestly give, because it assumes uniform thickness, level ground, standard access and a plain finish. Sydney jobs frequently have none of those four: only 55.8% of Sydney dwellings are separate houses, so much of the work is courtyards, terraces and side passages where the truck cannot reach the pour.
Use a calculator to sense-check a number. Never use one to accept or reject a quote.
Frequently asked questions
Is $125 per square metre a fair rate for a plain slab in Sydney?
It is a fair typical rate for 2026. Whether your job sits above or below depends on size, access, finish, reinforcement and soil. A 40 square metre slab on flat ground with truck access should land near or below it.
Why is my quote higher than the online average?
Usually access or soil. Tight side access needing a pump adds $600 to $900 per day, and reactive clay can add thousands to a house slab through extra reinforcement and deeper edge beams.
Does the price include GST?
Check. Published ranges vary and so do quotes. Compare GST inclusive against GST inclusive.
How much does concrete cost per cubic metre?
$345 to $550 at 25 MPa delivered and supplied only, typically around $435. Higher grades cost more and small loads carry surcharges.
Can I get a price before I have engineering?
For pads, sheds, patios and paths, yes. For a new dwelling the slab follows soil classification and engineering, so earlier figures are indicative.
Does a slab need a structural engineer in NSW?
House slabs do. Garage floors, alfresco slabs and paths on stable ground generally do not, but confirm with your certifier.
Ready to price your slab properly? Request a quote and we will itemise every component, or call 02 9054 3040. We work across Western Sydney and the wider metro area, with the full list of service areas here. Licensing and process questions are covered on our concrete FAQs page.
Licensed Sydney concreters pouring residential, commercial and council concrete since 1999. Every job is worked to engineer-certified specifications by our own crew.
NSW Fair Trading Lic. 219967c · ABN 13 160 436 902 · Fully insured



